Fjernlås nøkkel PASSAT 3b 98 Modell

[Thomas3B]

Hei! Har nylig kjøpt meg en passat, så er fjernlås defekt, pga alle låsene i bilen har blitt byttet ut, nøklene må omprogrammeres for å kunne virke igjen på de nye låsene, noen som vet om dette er lett å gjøre, eller evt hvor mye det koster? hadde vært greit å bare trykket på knappen på nøkkelen, i stedet for å låse opp døra hele tia :P

[TKarlsen]

Møller gjorde det gratis på bilen min :D Var en av dagene før jul, lite med folk som jobbet. Og han som tok bilen orket ikke å styre med ordre og ta betalt. Så jeg fikk det som en julegave sa han :P

[Thomas3B]

Møller gjorde det gratis på bilen min :D Var en av dagene før jul, lite med folk som jobbet. Og han som tok bilen orket ikke å styre med ordre og ta betalt. Så jeg fikk det som en julegave sa han :P

 

Tok å spørte dem på facebook nå, problemet er at det ikke er noe møller bil i nærheten her :P

[Quattro73]

Koster ingenting å prøve; http://www.bilforumet.no/bilmerker/audi/a4-s4-rs4-b5-1994-2001/299590-nokkel-fungerer-ikke-pa-sentrallas.html#post2943756

 

VW/AUDI/SEAT/SKODA

 

 

 

Remote Control Programming (1997 ON)

 

1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second key.

3. Using the remote control press the Unlock button once, and the horn will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding procedure. The remote control will now be programmed.

 

NOTE : When performing programming on additional remotes the procedure is the same, except you press the unlock button 2, 3 or 4 times for the different remote.

For example : If programming 2 remotes press the unlock button twice with a 1 second interval between each press, repeat for 3 and 4 remotes.

 

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote control.

Endret Februar 12, 2013 av Quattro73

[TKarlsen]

Koster ingenting å prøve; http://www.bilforumet.no/bilmerker/audi/a4-s4-rs4-b5-1994-2001/299590-nokkel-fungerer-ikke-pa-sentrallas.html#post2943756

 

VW/AUDI/SEAT/SKODA

 

 

 

Remote Control Programming (1997 ON)

 

1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second key.

3. Using the remote control press the Unlock button once, and the horn will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding procedure. The remote control will now be programmed.

 

NOTE : When performing programming on additional remotes the procedure is the same, except you press the unlock button 2, 3 or 4 times for the different remote.

For example : If programming 2 remotes press the unlock button twice with a 1 second interval between each press, repeat for 3 and 4 remotes.

 

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote control.

 

Var nok den de tok på bilen min. For det tok ikke lange tiden å fikse det

[Thomas3B]

Koster ingenting å prøve; http://www.bilforumet.no/bilmerker/audi/a4-s4-rs4-b5-1994-2001/299590-nokkel-fungerer-ikke-pa-sentrallas.html#post2943756

 

VW/AUDI/SEAT/SKODA

 

 

 

Remote Control Programming (1997 ON)

 

1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second key.

3. Using the remote control press the Unlock button once, and the horn will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding procedure. The remote control will now be programmed.

 

NOTE : When performing programming on additional remotes the procedure is the same, except you press the unlock button 2, 3 or 4 times for the different remote.

For example : If programming 2 remotes press the unlock button twice with a 1 second interval between each press, repeat for 3 and 4 remotes.

 

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote control.

 

 

TUSEN TAKK! er på skolen nå, men skal prøve dette i storefri :)

[Thomas3B]

Funka ikke, men ellers takk for hjelp :)